When a single water source needs a second zone
If your irrigation layout has grown beyond one line of emitters, you may want to control each zone separately without adding another tap. The 13mm Valve is designed for exactly that: it lets you set up a secondary zone of watering from a single water source. It is not necessary for every irrigation layout, but it becomes useful when you want to run and have control over multiple lines of irrigation.
The valve gives simple on/off operation, so you can control your emitters and water usage precisely. Think of it as a gate in the line rather than a pressure regulator — it opens or closes flow to the zone downstream.
What the 13mm Valve is designed to work with
- Irrigation Kit | 13mm Valve: Designed for use with our Adjustable Drip, Adjustable Spray and Under Tree Sprinkler Irrigation Kits. Match the valve to your existing kit family before planning a second zone.

Irrigation Kit | 13mm Valve - Irrigation Kit | 13mm Valve: The 13mm Valve allows a secondary zone of watering to be set up from a single water source. This is the core reason to add the valve: one tap, two controllable zones.
How to install the 13mm Valve in-line
The valve must be installed in-line, with tubing connected to both ends and secured with two 13mm Ratchet Clamps. Follow this sequence to place it correctly.
- Plan the zone boundary: Decide where the secondary zone begins. The valve sits at that point in the line, with tubing running to both sides.
- Cut the tubing cleanly: You need two tubing ends to connect to the valve. Cut at the chosen point so both ends reach the valve comfortably.
- Connect tubing to both ends: Push one tubing end onto each side of the valve. The valve is in-line only — it is not a end-of-line cap.
- Secure with two 13mm Ratchet Clamps: Use one clamp on each tubing connection. The supplied evidence specifies two 13mm Ratchet Clamps for the valve installation.
- Check clamp stock before you start: All irrigation kits come with enough 13mm Ratchet Clamps for the included fittings, but the 13mm Valve may require additional clamps. Confirm you have two spare clamps for the valve before cutting tubing.
- Test the on/off action: Turn the valve through its on and off positions to confirm it operates smoothly and that both connections are secure.
Clamps and fittings: the details that decide whether the valve works
The valve itself is only part of the installation. The supplied information is explicit that it must be secured with two 13mm Ratchet Clamps, and that while kits include enough clamps for their included fittings, the valve may need additional clamps. Additional lines of irrigation may also require additional fittings. Before you cut into a line, count what you need: two clamps for the valve, plus any clamps and fittings for the new secondary line.
This is a small, low-cost part — the catalog price is USD 2.79 against a comparison price of USD 4.65 — but a missing clamp is the kind of detail that turns a simple job into a second trip to the shed. Treat the clamp count as part of the valve purchase, not an afterthought.
13mm Valve at a glance
- Irrigation Kit | 13mm Valve: Simple on/off operation gives precise control over your emitters and water usage. The valve is a shut-off control, not a fine-tuning regulator; use it to isolate a zone.
- Irrigation Kit | 13mm Valve: The Valve must be installed in-line, with tubing connected to both ends and secured with two 13mm Ratchet Clamps. Plan for an in-line position and two clamps; it is not a push-on end fitting.
- Irrigation Kit | 13mm Valve: While not necessary for every irrigation layout, the 13mm Valve allows a secondary zone of watering to be set up from a single water source. Skip it if one zone covers your garden; add it when you need independent control.
Using the valve day to day
The valve's job is simple on/off operation. Open it to water the secondary zone, close it to shut that zone off while the rest of the system continues. That makes it useful for isolating a new bed, a section of pots, or a line you only want to run occasionally — all from the same water source.
Because the supplied information describes on/off operation rather than gradual adjustment, treat it as a zone switch. If you need to change the output of individual emitters, that is a job for the emitters themselves, not this valve.
Checkpoints before you cut the line
- Confirm your kit family: The valve is designed for use with the Adjustable Drip, Adjustable Spray and Under Tree Sprinkler Irrigation Kits. Check that your layout uses one of these before buying.
- Count your clamps: You need two 13mm Ratchet Clamps for the valve. Kits include clamps for their own fittings, so check whether you have two spare.
- Allow for extra fittings: Additional lines of irrigation may require additional fittings beyond the valve and clamps.
- Choose an accessible spot: You will operate the valve by hand, so place it where you can reach it without moving plants or dismantling the line.

